sea snark sailboat

Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.

• Sailboat Guide

Sea Snark (Super Snark)

Sea Snark (Super Snark) is a 10 ′ 11 ″ / 3.4 m monohull sailboat built by Snark Sailboats (Meyers Boat Co.), Cleatline Boats, and CastleCraft starting in 1958.

Rig and Sails

Auxilary power, accomodations, calculations.

The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.

Classic hull speed formula:

Hull Speed = 1.34 x √LWL

Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio .311 Hull Speed = Max Speed/Length ratio x √LWL

Sail Area / Displacement Ratio

A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.

SA/D = SA ÷ (D ÷ 64) 2/3

• SA : Sail area in square feet, derived by adding the mainsail area to 100% of the foretriangle area (the lateral area above the deck between the mast and the forestay).
• D : Displacement in pounds.

Ballast / Displacement Ratio

A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.

Ballast / Displacement * 100

Displacement / Length Ratio

A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.

D/L = (D ÷ 2240) ÷ (0.01 x LWL)³

• D: Displacement of the boat in pounds.
• LWL: Waterline length in feet

Comfort Ratio

This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.

Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam 1.33 )

• D: Displacement of the boat in pounds
• LOA: Length overall in feet
• Beam: Width of boat at the widest point in feet

Capsize Screening Formula

This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.

CSV = Beam ÷ ³√(D / 64)

Early SNARKs were one of the most popular sailing boats ever. This is partly due to the fact that they could be purchased with ‘product coupons’. For example, a large number of Kool cigarette coupons could be redeemed for a SNARK with the Kool logo on the sail. It was also possible to purchase a SNARK with the KOOL logo (without smoking a single cigarette) for $99. The Kool ad campaign reportedly received 18000 SEA SNARK orders in 1971 alone! Most later SNARK’s are made of styrofoam with an outer layer of ABS for improved durability. (Although the boats that were part of ad campaigns were usually built of styrofoam without the ABS shell.)

Embed this page on your own website by copying and pasting this code.

• About Sailboat Guide

©2024 Sea Time Tech, LLC

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

• Seacycle 
• Spring Creek

Popular Options

The Sunchaser I and the Sunchaser II share the same hull.  Sail rigs are interchangeable.

Click Here for Parts for Sunchaser II

Sunchaser  on the Water Video       

Sunchaser Sailboat Voyage  Video (This shows an earlier version of the Sunchaser Sailboat in this video)

Sail and hull colors may vary from those depicted in photographs.  All equipment, specifications and materials may change without prior notice. 

Ian Schaefer

some things

Super Snark Sailboat

I just bought this sailboat, an 11′ Super Snark. I’ve wanted to learn to sail for a few years—this seemed like the perfect sailboat with which to start. It is purportedly unsinkable and very stable. The ABS clad EPS foam hull certainly seems very durable and indeed, could not possibly sink even if completely swamped.

I had it out for the first time this weekend and had a fantastic time. This was my very first time sailing, but I found the boat quite easy to handle – the basic sailing instructions I’ve read were enough to get me underway with this small sailboat. With a little ‘effort’ I was even able to capsize the Super Snark and shortly thereafter learn how easy it is to right this boat. I’ll save the details of that story for another time.

After the first trip out I realized that all the wood parts – rudder, tiller, keel, transom – needed some attention. The marine plywood rudder was delaminating, and though it would be simple to cut a new one, I thought it might be worthwhile to repair it. After gluing and clamping the rudder in several places, I sanded and varnished all of the wood parts.

I also plan on painting the outside of the hull – navy blue. I’ll keep the white gunwhale and medium blue bumper as is. This motif should work nicely with then existing blue-white-blue-white striped sail and equally well with an Egyptian cotton colored sail I’d like to have.

Super Snark Links

• CastleCraft Repair Tips for Snark Sailboats
• CastleCraft Super Snark Sailboat Parts
• Snark Sailboats Group on Yahoo! – Membership required
• How to Sail a Boat – wikiHow [This article is short and to the point. I think it’s worth a read if you are new to sailing.]
• Grog’s Boating Knots Index [Note: start with the figure eight and bowline knots.]

Want a New Snark Sailboat?

I was surprised to learn that Snark sailboats are still being made – not only the Super Snark, but also the Sea Skimmer, Sunflower, and others. If you don’t have the time or inclination to repair an older boat, a shiny new Snark is still a relatively affordable way to start sailing. Here are a few links to the best prices available through Amazon.

Rigging the Super Snark

More Snark Upgrades

Splash Deck – I am planning to sail in the bay at Stone Harbor, New Jersey in late September. It can get choppy there – and while the summer boat traffic will have diminished I have yet to deal with the wake of a decent sized powerboat. The splash deck covers the area of the otherwise open hull from the mast step forward to the bow, shedding water the boat might take on from chop and wake. Coming over the bow. I am nearing completion of a wooden splash deck and I am excited about my design and the results. I will post photos and detail soon. Boom Vang – Provide downward tension on the boom for better sail shape and to minimize ‘bounce’. Use the free end of the halyard through the gooseneck of the boom and back to the cleat.

Traveller – create a bridle using a short length of line between the two screw eyes on the inside of the transom, leaving enough slack in the line to come up and over the tiller with clearance. Thread a small block on the bridle before fastening the line on the eyes. Then the tack end of the main sheet is secured to the dead eye of the block allowing the tack to travel along the bridle.

Tiller Tamer – Loop a short bungee cord around the tiller and connect to the screw eyes on the inside of the transom. This should exert just enoungh tension on the tiller to bring the rudder back to center when the tiller is released.

Daggerboard Retainer – attach on or two screw eyes into a small plywood plate on the stern end of the daggerboard trunk. From these eyes, run a bungee cord around the aft edge of the daggerboard. Pulling on the bungee allows the daggerboard to be raised or lowered – releasing it should hold the board in any vertical position.

Kickup Rudder – Design and make a two-piece rudder to replace the old one-piece rudder, allowing for easy beaching of the sailboat.

82 thoughts on “Super Snark Sailboat”

I just bought my first sailboat, a 1972 Sea Snark. It has the ABS coating but is bubbling and cut in places. Is this something I will need to replace and cover with fiberglass or is there and easier way to eliminate the bubbling and fix the small cuts everywhere. Not opposed to the fiberglass and it will have a great finish – just don’t have any clue what it’d be doing. Doesn’t look terribly hard to do though. Thank you for any help.

P.S. This is a great forum, thank you very much for creating it. Lots of great help, ideas and information.

Am I the only person in the world to own Snark Mayflower??? Mine needs some minor hull repairs, but its a wonderful boat. I am “older” and cannot handle the heavier boats, so this boat is great for me. I am wondering if anyone has made a pvc trolley for a 90# (without rigging) boat? I am thinking something with a sling in the rear? I plan to use larger all plasitc wheels, but the design is making me nuts. In the past have used a prebuilt hand cart with wood handle extensions, but now I want the stern at the rear of the trolley and that is the problem….suggestions? Also, when you painted did you remove the rubrail and what was that like???

I Love this site! Thanks!

Marci, not sure if you are still out there, but my dad is trying to repair the hull on our Mayflower, which we’ve been sailing on a small pond for years. He is 86 now. Years ago it smashed against a tree (the wind picked it up) and snapped in half. He repaired it at the time, but over the years it has taken on water, with a particular crack around the centerboard well. This summer he removed part of the skin and patched some of the holes in the foam with sections he created from an old styrofoam beach board. He also plans to build up the well internally. Not sure when he’ll be able to finish. I miss it dearly! I’ve tried buying a new hull for him in the past but could never find any for sale.Happy sails to you.

I can’t help you, except to say that, yes, someone else once owned and enjoyed the Snark Mayflower from 1974-1978. I used to carry it on my back over the rocks at Folly Cove on Cape Ann, Massachusetts each time we wanted to sail. My wife is writing a memoir of an one hour Gilligan’s Island sail that four of us took across Ipswich Bay in gentle swells . By the time we reached Plum Island seven hours later, they had turned into 10 foot breakers. Yes, a wonderful boat, so sturdy for being only a piece of foam and plastic. I found your post because my wife didn’t believe it was called a Mayflower, and I had began to believe our little Mayflower never existed. Do you have any pix? Love to see one again.

I just acquired an old super snark – no sail, rudder or daggerboard. I got it to learn to sail. I had read that this was the way to go and I thought I got a great deal – $40. However, I am now concerned – the thing is a lot more than 50 lbs. it took my husband and I a lot of effort to lift and slide into our van. Someone suggested water issues? Could there be a heavier model out there?. This has some kind of coating over the styrofoam. any thoughts to help me figure out whether to invest more money into parts.

Today, I went to the beach front with my kids. I found a sea shell and gave it to my 4 year old daughter and said “You can hear the ocean if you put this to your ear.” She placed the shell to her ear and screamed. There was a hermit crab inside and it pinched her ear. She never wants to go back! LoL I know this is entirely off topic but I had to tell someone!

My web blog: Golf Star Hack Download ( Irwin )

Peter, there are some photos of the Snark Mayflower here. I am a writing coach—you can find me at my writing coach dot net if your wife needs any help with her memoir! We are not far from Plum Island and would love to hear the tale. http://photobucket.com/images/snark%20mayflower?page=1

Dear all, how nice to found you all in the www. My Sunflower hull is delaminating arround the dagger board. Does someone have ideas and experiance in how to fix this? Thank you so much. Daniela Is there a overview of serial-numbers available, that will tell the year of manufacture?

Last fall I saw a Sea Snark at a thrift shop and got it for $65. A small hole in the sail but serviceable. A busy spring / summer but finally got my chance to sail two days ago. Wow what a rush. I went out in 3 mile/hour wind and gradually increasing to 5. The wind was was fluky and changing direction and after 2 1/2 hours this old guy at 69 was bushed. Looking at videos and instructions for rigging the main sheet I could see many versions. I saw one photo with a traveller. I wondered about needing a hiking strap but wondered if the hull might crack in half. Reading here about a bow splash. My idea is to keep the boat light so I will not add anything slick to the styrofoam. I think I should graduate to a bigger boat for such niceties. Going sailing alone on this craft is the way to go and encourage others to club for racing. This Sea Snark and some lawn mower racing. Retirement is great. Thanks to all to you who have suggested repairs and improvements to this newbie.

Wow…happened to come across this site and am glad to have found it. I purchased a Snark back in 1972. It had been stored in my parent’s garage and now that I have a cottage on a lake, I am going to restore it. I need to replace the sail for mice have wrecked havoc to the old one. In 1972, I fiber-glassed the bottom and that needs to be repainted, will decide on a color once I decide on he sail. I need to do a little repair for a mouse nest in the bottom had caused some damage. I think I have all the parts. I am looking forward to reading the rest of the thread. Hard to believe it has been 42 years…

Snagged an older Snark from neighborhood group site (!) and been out three times so far – is great!

Two questions:

1) I want to fortify hull – Snark people suggested using 2 part epoxy, but NOT marine grade (will melt the styrofoam) – any suggestions on a decent, but reasonable option and how much it takes to do the whole hull?

2) The third time we went out, my son and I were going pretty fast but maybe because we were causing a bit of waves (?) the boat suddenly filled with water – less than a minute. Yikes! I had to bail like a madwoman (once the water is higher than the centerboard hole it is pretty hard!!). I need to make a splash guard – can you post a pic of the one you made? So many thanks!!

What do you do when you’re on the water, swilling and you need to put the sail down? I have a super Snark. The sail does not come down at all and in very windy conditions, this could be dangerous.

I am coming late to the party here, but just retired and am determined to get my “freebie” 1969(?) Mayflower in the water. I had to buy a new sail for it because the one on it was roached. Is there somewhere I can see a diagram to show this newbie how to properly rig this little boat? Thanks in advance!

I have found an excellent repair for styrofoam to the plastic hull. I fixed the centerboard trunk works excellent. It’s called 5200 from 3M, very messy but works great an won’t harm styrofoam. I got it at Home Depot, an it’s not cheap. $14.00 a tube.

I have a 11′ Snark Sunflower in my garage (it was left by the home’s previous owner). It looks in great shape, as if it rarely saw the water! If anyone has an interest in purchasing, please contact me. I’d be happy to send pictures to anyone interested. Alan 215.630.9508 Newtown, Pa

The sail should come down by loosening the halyard. Here is a video on proper assembly and you will see how the halyard line is used to raise and lower the sail: http://www.sailboatstogo.com/content/Super_Snark_Sailboat_Delivery_Assembly_and_Rigging

Super Snarks are being sold on SailboatsToGo.com here; http://www.sailboatstogo.com/content/Snark_Super_Snark_Sunflower__Sailboats

Here is a new video of my granddaughter sailing a Super Snark: https://youtu.be/JMfLjxqQTeg

This page has links to 3 videos of the larger Snark, the Sunchaser. http://www.sailboatstogo.com/content/Sunchaser_I_Snark

This page has the history of the brand: http://www.sailboatstogo.com/content/Snark_History

This gadget makes the mast taller so you get more headroom under the boom: http://www.sailboatstogo.com/catalog/PARTS/5211

I have a super snark. we stored it in a storage unit for a number of years. but my dad back in the 80s took 4 inch PVC and put two screw fittings on the ends and created a tube to protect the sail during transport and storage.

Hey! I just got a Snark Sea Skimmer off of craigslist for just a few dollars. The Hull is in pretty bad shape (lots of duct tape patches) and the deck has some cracking i’m sure from age. It is in one piece tho and all of the pieces parts are there. Any suggestions on where i should get started on repairing the Hull? Products, techniques?

Hello, I also just purchased a Super Snark and have repaired the hull, a few dents and cracks with PC-11. Going to sand it a bit and then paint it. The original color is red but I may want to change it. Just wondering how the Krylon Fusion paint held up. I also think the Navy blue would be beautiful! Enjoying learning from fellow sailors! Thanks

Hey all –

I just did a Super Snark restoration in August and September. There is a yahoo user’s group for Snark sailboat owners which is active and helpful.

I have a photo album there showing my restoration from a hull that sat in the weeds for years to a fun and portable sailboat. Good luck!

I used Krylon fusion on my Snark and it worked great!

Hey I was wondering all the dimensions of the Rudder and dragger Board? I received a super snark in excellent condition for free. it just doesn’t have mast sail dragger board or rudder and I plan on making most of it my self any help or suggestions will be appreciated! New to sailing so be easy on me! Thanks again! Devin

I’m about to buy a very old snark, the unclad Kool cigarette version. Has anyone had any problems with these, as far as the hull breaking or getting waterlogged, etc.? Thanks!

Does anyone know what happen to the Snark Sailboat Owners Yahoo Group? I just bought a Sunflower. I have joined, but being a restricted group, its been more than a week and I have not heard back. I also tried to go to the group website and it is not working. (www.wisdomsecurity.com). What I wanted to know is: Has anyone set up a jib on a Sunflower? How did it work? How it was done? Thanks.

I have a 1972 Kool Snark. Smoked Kools to have required cartons and $99.00 to buy it. We did an amateur fiberglass job on it in 1972 but it has served the family well on lake and beach adventures. Would like to sell it. Any takers?Contact cbrittain47 @carolina.rr.com

What a treasure trove of information!

First of all, if anyone knows of a Snark Mayflower for sale in the eastern half of the US, please contact me. I will come and buy it.

Second, yes, the Snark Mayflower did exist. They discontinued them in…maybe 1979? Or in the 1980s?

My Uncle bought one in the late 1970s and had it at his lake cabin in Minnesota. I learned to sail on it in the late 1980s. I sailed it off and on for years when I was up there in the summer. It was a wonderful boat, simple to sail, and basically impossible to capsize. I sailed it one time for the first time in like 10 years in 2011. I have a blog post about it here: http://craigsteffen.net/blog/2011/07/2011_07_18_23_21_50_A.php Not a year after that, possibly that summer, it was apparently beyond repair and my uncle cut it up and threw it away.

The Mayflower hull (and some of the other Snark boats too) is a styrafoam core with a plastic outer shell. Having talked to people, apparently it’s generally fine if you keep it indoors when it’s not on the water. If you leave it outside all the time, however, the plastic will eventually develop cracks and let water in. My uncle had repaired it with fiberglass several times but finally just couldn’t keep up with it. When it cut it apart water poured out of the voids in the hull.

There is, by the by, a supplier in Europe that sells them. The Snark supplier in the US says that they will not ship them to the US, and the company is uninterested in resurrecting the design.

I would love to make one myself. There are drawings around. I could almost do it with photos and dimensions memory. I think cutting the shape out of styrafoam wouldn’t be too terribly hard; I’d then have to figure out how to make the hard outer shell. Fiberglass? Maybe carbon fiber is cheap enough nowadays?

If you’re looking for information on it, here’s a great resource: http://www.castlecraft.com/snark_assembly.htm It’s a collection of Snark product assembly manuals. It includes discontinued products like the Mayflower: http://www.castlecraft.com/PDF/Snark-Mayflower-Manual.pdf

Craig Steffen [email protected] 217-979-2392

I have a 1972 Sea Snark for sale. It’s in great condition & only used 4 times since refiberglassed. It’s to heavy for top of my new car

Just acquired a snark mayflower for 40 bucks. Out of the shark models, I have struggles to find much for any info on the mayflower specifically…anyone else own one?? The ABS had gouges and cracks that we have been working to repair. Where the rubber molding strip attaches, there is silicone or similar product that was used to seal the seam and it’s a real bear to remove. Anyone have any suggestions on what we can use to make it easier that will be safe to the foam and ABS? Think we could just cut a 2in strip off all the way around on both the inside and outside ABS peices and use fiberglass cloth or something to replace that area? I appreciate any input. Thanks.

Anyone tried fitting a 55 f sail (with adj to mast etc) to the supersnark? Any info on this? Stability?

Hi John G – I was wondering the same thing! I’ve just come upon one of the ABS-clad supersnarks and was curious about sail surface area upgrades. Are you still around, and did you try anything with any success?

I just purchased a 1989 super snark and am painting and restoring. Bought a beautiful new sail from sailboatstogo. will sail and post pics next week when I can figure out how to post them

Leave a Reply

Your email address will not be published. Required fields are marked *

Save my name, email, and website in this browser for the next time I comment.

SHOP NOW:    SUPER/SEA SNARK SAILS         SUNFLOWER SAILS       NEIL PRYDE DACRON       WHITE DACRON

Sea skimmer sails      sunchaser & mayflower sails    66 sq ft sail        batwing sail       snark parts,   about our sails.

SailboatsToGo offers our own nylon sails, original Snark nylon sails, Sailmaker Neil Pryde dacron sails, white dacron sails, and sails for the Snark Sea Skimmer and Sea Devil. 

Satisfaction guaranteed! Our nylon  sails are very well made durable nylon sails that will fit Super Snark, Sea Snark, Sears Whirlwind, Spring Creek, SailboatsToGo (that's us!),  Paddle ski,  Sea Eagle, and  SOAR .  Our  Snark Sailboat sail is 45 square feet, nylon.  It will fit your Sea Snark or Super Snark just like the original.   A great many Snark owners have bought these from us, we receive many messages from satisfied customers ( see Messages from Customers section below ) and we have never had a single one ask for a refund, but if you're not happy with it, you can be the first!  We also carry original equipment Snark brand nylon sails.  Usually arrives in less than a week.  Very low shipping cost.

Our white dacron and Sailmaker Neil Pryde International dacron sails are more durable and hold their shape better (stretches much less) than nylon in strong winds, which will give you better upwind performance.

These are all true, aerodynamic, shaped sails, which means they are cut and sewn to have the necessary camber (3-dimensional curvature) for creating aerodynamic lift.  They have sleeves for the boom and gaff and cutouts in the right places for tieing on the sheet and halyard and for the mast ring.   

These sails are used on canoes, ice boats, inflatable boats, kayaks and dinghies, in addition to Snark styrofoam boats

All major credit cards and paypal accepted. Address paypal payments & emails to [email protected] .  

Colors and Sizes and Types

Colors:  14 different sail color schemes!    Custom Graphics:   Add your logo to your sail.  $18 per square foot of logo $25 . Email us.  

Sizes :  The 45 square foot ("SF") sails fit Sea Snarks and Super Snarks and some older Sunflowers.  Also the Sears Whirlwind. All Sunflowers built after 1983 (and some older Sunflowers) take the 55 SF sail (scroll farther down this page for 55 SF sail offerings).   Some pre-1983 Sunflowers take the 45 and some take the 55, so that's where we have to take size identification to the next level.   Click Here

We have nylon sails below and we have dacron sails, farther down the page. Dacron is a premium-grade material that is stiffer and less stretchy, so the sail holds its intended shape better, even in strong winds and after years of service.   Within the Dacron category, we have a generic white sail, and we have name-brand Neil Pryde sails in various color schemes.  The Neil Pryde sails have premium-quality workmanship, such as heavier stitching and heavier reinforcement at stress points.

SUPER SNARK and SEA SNARK SAILS (45 square foot)  (also fit Sailboats To Go and Whirlwind)

SUNFLOWER 3.3 SAILS (55 square foot)  (Also Fits SailboatsToGo)

Do not assume all sunflowers take a 55 sf sail   explanation  .

NEIL PRYDE INTERNATIONAL DACRON SAILS (45 SQ FT and 55 SQ FT) 

Dacron (polyester) is a stiffer, less stretchy material than nylon.  A Dacron sail will hold its shape and not stretch out in strong winds.  It's also a heavier material and therefore stronger, as compared to nylon.   Neil Pryde is a widely-respected sail maker, known for quality workmanship.  You will be impressed with the extra heavy stitching on these sails, done with the greatest attention to detail.  Shipping cost will show up in your cart.  It's not much (around $10).   For an additional choice in a 45 SF colored Dacron sail see the Blue/White/Yellow OEM Snark Sail above.

WHITE DACRON SAILS (45 and 55 square foot)

This is a house brand sail (not Neil Pryde) but still very good quality.  As compared to nylon, dacron (polyester) is a stiffer, less stretchy material so the sail will hold its shape and not belly out in strong winds.  More Pictures and info click here .

66 SQUARE FOOT NYLON SAIL.

The 66 square foot sail is both longer and taller on the spars. Spar extensions are needed for both the boom and top spar.  If you already have spars for our 55 square foot sail, you will only need one spar extension:  $20 each.  If you have OEM Sunflower spars, you'll have to devise an extension for the boom.   This link if for extending the boom on SailboatsToGo spars:     Add Spar Extension to Cart  .   

BATWING SAIL

High tech modern design Batwing Sail. Great upwind performance in strong winds.  Reefable by means of zippers.  This is the modern Batwing sail from Balogh Sail Designs and includes a Free mast step that will adapt it to any of our rigs (not Snarks). Includes mast, boom, mast step, sail and rigging.  Available as an upgrade with our Canoe, Kayak, and Dinghy sailkits. (Click the "Upgrades and Options" link within any of those departments)

SEA SKIMMER SAILS

SNARK MAYFLOWER, SUNCHASER I AND SUNCHASER II SAILS

Other items of interest to Snark owners

Spar Set and Mast :  Our unique folding design makes these low shipping costs possible for mast and spar set.  If you go elsewhere, ask about their shipping cost before you order!   (You'll be shocked.)  

Spar Set  The two poles that go in the sail sleeves and the ring that accepts the mast. More Info

Mast: More Info

Stabilizer Pontoons prevent capsizing:   More Info

Alternatives to Styrofoam Sailing:  When the rest of your Snark wears out, or even before that, if you want a sailboat that is dryer, more comfortable (back support!) and more portable, check out our inflatable sailboats and canoe sail rigs.  You can use your Snark sail and spars and save!   Click Here For More Information.

Messages from Customers

"Thanks so much for sending the sail out so promptly.  It arrived yesterday.  It's all set up in the backyard right now for my son to see for his birthday present!  It was a pleasure doing business with you."   --   Robyn M.

"Love doing business with your company.  I'm telling all my friends to buy sails from SailboatsToGo!" -- Joe L. 

"...went out yesterday with my daughter. We had a wonderful time and everyone commented on the beauty of the sail. Thanks for your prompt response.  I am very pleased with your sail and service and will recommend you." -- Mark Y.

"The new sail seems to be superior to the old Snark original in both material choice and construction."    Martin M.

"We received the sail for the Snark Sunflower on Wednesday.   Thank you for your prompt replies and shipment of the sail. We installed the sail and took it out last night.  It fit well, and worked well also. My son and I are very pleased with the sail and again thank you for the great response to my inquiries.  This has enabled my son to enjoy the sailboat a few days before he leaves home for 2 months.  I will happily recommend your business to anyone who needs sails and related items. Thank you very much!"  Tom and Seth B.   June 2011

"Hi, Jim - Just a note to let you know I just spent a very enjoyable weekend sailing our Super Snark with the new spar set we ordered earlier this month. Set up went very smoothly, thanks to the excellent set of instructions you supplied. The pictures were especially helpful. I found your spar set to be far superior to the original tubing and fittings that were on our Snark. That mast slide sure instills confidence compared to the flimsly fitting on the original. I hope to enjoy sailing on our pond here on Cape Cod as long as the weather holds up. Thanks again for your prompt service and excellent product." -  Chris

Want more? Read our Ebay Feedback and see how pleased people are with our products and service.  (Our prices here are generally lower than on Ebay, so come back here to make your purchase.)

Use Our Sails in Do-It-Yourself Sailboat Projects

This Snark sail is also a good choice for do-it-yourself sailboat projects, such as ice boats, converting a dinghly you already own, or putting a sail on your canoe or inflatable.   Click on the "Products" link at the top of this page and then on "Plans" to buy plans for canoe sail rig or inflatable sailboat rig that would utilize this sail (although the plans also tell you how to make your own sail if you prefer).  

Interesting Facts About The Snark Sail Design

The Snark Sail is referred to as a "Lateen" style sail, which means the mast is short and the sail has another spar, called a gaff, which carries the peak of the sail up much higher than the top of the mast, with the gaff slightly angled so that the lower front corner of the sail is in front of the mast.   The Lateen style sail originated in ancient times and is still used all over the world on small boats, especially in India and the Arab world.  Those fishing and trading vessels often use rags and old grain sacks stitched together for sail cloth.  A Lateen sail can hold its own against a sloop rig of equal total sail area (sloop rigs have a jib and mainsail) in a race of otherwise equal boats and crews.  Don't believe what some say about jibs increasing the efficiency of the main.  Snark and SailboatsToGo and other users of the Lateen sail plan are continuing a long and proud tradition in sailing. 

Expedia Rewards is now One Key™

Elektrostal, visit elektrostal, check elektrostal hotel availability, popular places to visit.

• Electrostal History and Art Museum

You can spend time exploring the galleries in Electrostal History and Art Museum in Elektrostal. Take in the museums while you're in the area.

• Cities near Elektrostal

• Places of interest
• Yuri Gagarin Cosmonaut Training Center
• Central Museum of the Air Forces at Monino
• Peter the Great Military Academy
• Bykovo Manor
• Balashikha Arena
• Malenky Puppet Theater
• Balashikha Museum of History and Local Lore
• Pekhorka Park
• Orekhovo Zuevsky City Exhibition Hall
• Ramenskii History and Art Museum
• Noginsk Museum and Exhibition Center
• Saturn Stadium